Certa CTGDN5IN1CUTA Troubleshooting Guide

ACCESSORIES• Pole Chain Saw Head assembly (with attachment tube)• Extension Tube assembly• Pole Hedge Trimmer Head assembly• Allen Key• Spanner• Nylon

3 – Tighten the knob bolt securely.Installing the Handle1 – Insert the barrier handle into the top handle.2 – Fasten the 4 internal hexagonal screws w

2 – Turn the adjusting screw until the chain fits but may be moved with ease.Bar and Chain Replacement1 – Unscrew the fixing nut and remove the chain

Installing the Guide Bar and Saw Chain1 – Replace the sawing chain onto the sawing rail.2 – Position the guide bar so that the chain tensioning studs

CHANGE CHAINSAW TO HEDGE TRIMMER1 – Unscrew 2 internal hexagonal screws with allen key and push the saw attachment out:2 – Insert the hedge trimmer at

2 – Insert attachment into main shaft. Fix the lock lever into the hole.3 – Tighten the knob bolt securely.OPERATIONSBefore Use Checks WARNING!For yo

FUEL• Mix unleaded petrol with air-cooled 2-stroke engine oil at a ratio of 25:1• These engines are certified to run on unleaded fuel.• Make sure to u

3 – Press the primer several times until the fuel overflow flows into the clear tube.4 – Move the choke lever to the closed position.5 – Set the stop

8 – Allow the engine to warm up for several minutes before starting operations.NOTES• When restarting the engine immediately after stopping it, leave

Adjust the pump as follows:1 – Stop the engine and make sure the stop switch is in the OFF position.2 – Place the unit on its side with the oil reserv

Table of ContentsSAFETY WARNINGS...

Adjusting the Angle of the Cutting Blades1 – Stop the engine.2 – Lift the lock lever and press down on the adjusting lever.3 – Adjust the angle of the

MAINTENANCEGood maintenance is essential for safe, economical and trouble-free operation. It will also help to reduce pollution. DANGER!Improper maint

ENGINE CAREAir CleanerIf the air cleaner is clogged, the engine performance will be drastically reduced. Check and clean the air filter element in war

HEDGE TRIMMER CAREBlade• When refilling the tank or resting, it is often a good idea to use the time to oil the cutting blades.• If a gap exists betwe

POLE CHAINSAW CAREOiling PortDismount the guide bar and check the oiling port for clogging.Guide BarRemove sawdust in the bar groove and the oiling po

SprocketCheck for extensive wear, and replace it when the teeth are worn over 0.3mm.Saw Chain CAUTION!It is very important for smooth and safe operati

After every cutter has been set, check the depth gauge and file it to the proper level as illustrated.Note: Be sure to round off the front edge to red

STORAGEAged fuel is one of the major causes of engines failing to start. Before storing the unit, empty the fuel tank and run the engine until is uses

Insufficient chain lubricationCheck Possible Cause ActionOil tank→Oil tank empty→Replenish oil tankGuide bar→Check that oil groove of saw rail isn&apo

Gear ratio (engine : cutter) 1 : 0.94Unit mass (without guide bar and chain, empty tanks) 7.5External dimensions (L x W x H) 2610 x 335 x 240Brush cut

Engine will not stop...

SAFETY WARNINGSYour safety and the safety of others is very important. There are important safety messages included in this manual and printed on the

Symbols on the machineryFor safe operation and maintenance, symbols are embossed on the machinery. According to these indicators, please follow instru

Work Place• Never start the engine inside a closed room or building. Exhaust gases contain dangerous carbon monoxide.• Never use the product:(a) when

• Never touch the muffler, spark plug or other metallic parts of the engine while the engine is in operation or immediately after shutting down the en

Kickback Safety Precautions – Chainsaw DANGER• Kickback may occur when the nose or tip of the guide bar touches an object, orwhen the wood closes in a

PRODUCT LAYOUT1 – Engine unit 2 – Shoulder Harness 3 – Handle4 – Extension Tube Assy. 5 – Hedge Trimmer Head Assy. 6 – Chainsaw Head Assy.7 – Fuel Tan